All Products

Eliminates stock rear turn signal bar and lights. Lightweight aluminum radius license plate mount adds a custom look. LED illuminated radius plate frame included.

Direct bolt-on for the OEM stock turn signal bar. Plug-and-play lightweight aluminum radius license plate mount. 20 dual-intensity red LEDs flush-mounted on either side.

T-6061 billet aluminum housings in gloss black finish. 15 super-bright white Daytime Running Light (DRL) LEDs per side. 15 super-bright amber turn signal LEDs per side. Available with smoke lens. Available for 56 mm forks. Sold in pairs.

Simple plug-and-play conversion to convert all of your Tour-Pak lights to run, brake and turn. Works with LEDs only. Greatly increases rear and side visibility. Note: Requires Custom Dynamics Smart Triple Play module PART #2050-0146 to operate; sold separately.

Quick-disconnect for any two, three or four wire auxiliary lighting product. Features 22 AWG wires, 15" total wire length, and four-pin JAE connectors. Sold in pairs. Quick-disconnect for any two, three or four wire auxiliary lighting product. Features 22 AWG wires, 15" total wire length, and four-pin JAE connectors. Sold in pairs.

Wide-angle super-bright LED clusters. Each cluster has three wires (low, high, ground) and can be used as single or dual intensity. Sold each.

A universal brake light flasher with 10 user-selectable flash/strobe patterns. Features overcurrent, thermal, short circuit, and reverse wiring protection. 84W, 12V system. Works with LED or incandescent bulbs. Dimensions: 2.25" L x 1.25" W x 0.5" H. A universal brake light flasher with 10 user-selectable flash/strobe patterns. Features...

Completely isolates turn signals from motorcycle. Provides outputs for aftermarket turn signals. Works with LED or incandescent bulbs. Max load of 5.0 amps per side. Short circuit and thermal protection. 4-way hazard compatible. Sold as pair.

Provides easy connection to run, brake, left and right turn, and ground wires.

Bolt on to the left and right sides of the Road Glide headlamp. Provide white LED running lights and amber LED turn signals. Feature a decorative stainless steel mesh to fill the void between the headlamp and fairing. Plug-and-play. Sold in pairs.

Aluminum trim with flush-mounted amber/white LEDs behind a smoked lens. White running light LEDs are automatically deactivated when the turn signals or hazard warning lights are activated, allowing for greater visibility of the turn signals. Direct bolt-on installation with included mounting hardware and wiring. Available in chrome or gloss black...

Wire adapters allow for installation of ProBEAM Dynamic Strips PART #s 2040-2832, 2040-2833, or 2040-2834 (sold separately). Plug-and-play.

Converts 2-wire Custom Dynamics Wrap-Arounds™ turn signals to 3-wire, allowing them to function as both running and turn signals. Sold in pairs. Converts 2-wire Custom Dynamics Wrap-Arounds™ turn signals to 3-wire, allowing them to function as both running and turn signals. Sold in pairs.

Steel gas tanks feature TIG-welded construction. Both styles measure approximately 20" L x 11" W x 8 1/2" T with a 3" deep tunnel. Mounting tabs measure approximately 23" center-to-center. All tank styles use L96-23 vented gas caps (sold separately) and hold approximately 3-gallons of fuel. Chrome mounting hardware included.

Kit delivers 17A at 1000 rpm and 38A at 2500 rpm. Get more power out of a smaller stator. Made in the U.S.A.

Kit produces 32A at 1000 rpm and 50A at 2500 rpm. Yields more charging power when upgrading from 32A or 38A. Improved durability and dependability over stock 48A system. Made in the U.S.A.

Kit includes stator, rotor, black rectifying voltage regulator and mounting hardware. Made in the U.S.A.

Controls voltage on Harley-Davidson and Buell alternators, unlike other rectifiers or regulators that dump to ground and cause maximum stator current and higher temperatures. Cycle Electric rectifying regulators block current to control voltage; this reduces stator current, resulting in low temperature and less drag on the motor. Made in the U.S.A.

Made from 6061-T6 aluminum and features a machined finish. Made to work with stock H-D aluminum hubs. All spacers/adapters are flanged for perfect alignment. Will not work with cush drive pulley.

Constructed of fiberglass with a gel-coat finish. Available with exhaust cutouts. Bags only; accept stock H-D lids and hardware. Mounting holes come pre-drilled. Right and left sides sold separately. Made in the U.S.A.

Adjusts to the perfect angle for each rider. Allows use of 1-1/4" T-Bars as well as 1-1/4" base risers (gauges not included). Available in chrome. Made in the U.S.A.

Attitude-style sissy bar sticks. Attitude style made from 9/16 inch round cold-rolled steel. Daggertude and Squaretude styles made from 9/16 inch square steel bar. Available in approximately 18 inch or 30 inch heights. Side plates must be purchased separately.

Polished stainless steel bag draggers. Mount to bottom of most extended bags to prevent paint damage to bottom edge of bag while cornering. Measure 19.5" long and 1" wide; mounting hardware included. Sold in pairs. Made in the U.S.A.

Made of high-quality steel with a black powdercoated finish. Comes with fastening mechanisms. Will work with fixed or detachable sissy bar side plates. Saddlebags sold separately.

Made of high-quality steel with a black powdercoated or chrome finish. Comes with fastening mechanisms. Will work with fixed or detachable sissy bar side plates. Use with 93-21 style OEM-style hard-sided saddlebags. Made in the U.S.A.