All Products

Kit neatly organizes Deutsch pins and plugs in one complete package. Includes storage bin, pins, stamp sockets, and receptacles/plugs. Available with black plugs and receptacles. Made in the U.S.A.

Refill your Deutsch Builder Kits with these connector components. Each connector features a silicon rubber seal to reduce corrosion and moisture. Receptacles and plugs come complete with required locks. Available with black or gray housings. Pins and sockets feature closed or open crimp-style ends.

Deutsch DTM components including receptacle kits, hole plugs, terminals, and sockets. Hole plugs keep connector watertight when wire is not present. Made in the U.S.A.

Deutsch plug and receptacle kits for fuel-injected models. Made in the U.S.A.

Extension harnesses intended for front turn signals mounted on handlebar switch housings. A must when installing taller handlebars. No crimping necessary.

100% Plug-n-Play wiring harness extensions. The simplest and easiest harness to fish through handlebars with no cutting or splicing. Some kits are complete systems including throttle-by-wire.

48” L wire extensions. For cut and solder applications. Wire ends are stripped but left with slugs to prevent fraying. Made in the U.S.A.

Front turn signal tap for adding additional front turn signals. Plug-n-play. Made in the U.S.A.

Match OEM H-D specs. Simple, plug-and-play installation. Made in the U.S.A.

Male and female connectors and terminals. Watertight construction in a small compact size. Simple to use. Made in the U.S.A.

Builder kit neatly organizes Molex MX-150 components in one complete package. Includes storage bin, various connectors, and terminals. Made in the U.S.A.

Molex MX-1900 connector components. Sold each, unless noted. Made in the U.S.A.

Intended for custom applications where momentary switches are used for a HIGH/LOW headlight switch and RUN/KILL switch. Module converts the momentary switch into a HIGH/LOW latching and an ON/OFF latching for a run switch. Made in the U.S.A.

AMP Multi-Lock connectors are direct Harley-Davidson replacements used since 1996. Non-waterproof connectors used on every factory model. Kit includes seals, wedgelocks, and crimp terminals. Made in the U.S.A.

Allows the use of exhaust systems with 18 mm O2 sensor bungs to be used with late model bikes with 12 mm O2 sensors. Reduces the 18 mm O2 bungs to 12 mm O2 bungs found on select 10-17 models. Wiring harness comes pre-assembled with connector pins.

OEM-type replacement connectors. Sold each. Made in the U.S.A.

Hard-to-find radio connectors, available in 23-position connector style. Sold each.

Allows you to bypass OEM O2 sensors when changing from the stock exhaust.

Includes all handlebar switch wiring, speedometer extension and twist grip assembly. Twist grip assembly includes adjustable PVC jacket for handlebar or riser wiring exit. PVC wire loom keeps round shape. All wiring is covered with smallest diameter loom required for a clean, professional look when installed.

All items needed to successfully extend the wiring to a set of OEM H-D handlebar switches. Harnesses include both male and female Molex terminals crimped on each end. Kits include heat shrink and color-matching wire.

Add additional running, brake and turn signal lights to the rear of your motorcycle. Plug-n-play (unless noted). Includes all the wiring and heat shrink required. Made in the U.S.A.

OEM replacement electrical power connection. For navigation, audio, tachometers, oil pressure gauges and heated grips.

Replacement mini fuses. Sold in 5-pack.

Pre-installed terminals that utilize MIL-SPEC crimping presses. Hardwired, like OEM CVO versions, from the sensor to the main connection on the harness. 100% plug-n-play. Made in the U.S.A.

Rubber reset switch boots. Sold in 5-pack. Made in the U.S.A.