New Products

Front 2" receivers available in different constructions for specific Polaris Ranger models. SP 570 series is constructed from 3/16" steel. XD 1500 series is constructed from 1/4" steel, mounts directly to the OEM bumper, and requires two holes to be drilled.

Constructed of 1/4" steel. Metal bead-blasted before being powdercoated black for best possible finish prep and supreme durability. Includes complete installation instructions and all mounting hardware. Made in the U.S.A.

Heavy-duty steel tow hook specifically designed for recovery. Metal-bead blasted before being powdercoated black for the best finish and durability. Easy to install. Complete installation instructions included. Made in the U.S.A.

Constructed of 3/16" Grade 50 steel. Metal-bead blasted then powdercoated for the best possible finish prep and supreme durability. Easy to install, with all mounting hardware and complete installation instructions included. Note: When your ball receiver is installed on the rear your Traditional 4x2 or 6x4, the tailgate may hit during dumping. The...

Works with UTV tubes OEM #105635 and PART #4501-1004. Works in standard 2" receivers. Zinc-plated. 5/8" diameter. Includes one pin and one clip.

Reduces wear and tear on your winch and roller fairlead while raising and lowering your plow blade. For use with standard or wide winches.

Constructed from 3/16" grade 50 steel. Hitches are metal-bead blasted before they are powdercoated for the best possible finish prep and supreme durability. Easy to install with all mounting hardware and complete installation instructions included. Made in the U.S.A.

KFI Formed bumper has two locations for 3" flush-mounted cube lights. Constructed of steel. Metal-bead blasted before powdercoated for the best possible finish prep. Powdercoated black-textured for supreme durability. Bumper tilts with the bed. Easy to install. All mounting hardware and complete installation instructions included. Made in the...

Constructed of 1/4" steel. Metal-bead blasted before being powdercoated black for best possible finish prep and supreme durability. Includes complete installation instructions and all mounting hardware. Made in the U.S.A.

12" L x 1.20" W. Can be used as a tie down loop. Designed to be used with plow pulleys as an attachment point for your hook.

Constructed of 3/16" steel. Powdercoated black for supreme durability. Includes upper hook attach hole and complete installation instructions. No mounting hardware required. Made in the U.S.A. NOTE: Receiver will fit any standard four-hole winch mount without fairlead flange (3" x 4.875" bolt-up pattern).

Mounting plate remains attached to ATV/UTV and becomes a structural component, adding rigidity to ATV/UTV during plowing operations. Designed for high-ground clearance and quick plow installation or removal. Placed forward of footpegs to avoid any reduction of ground clearance. Quick-release pins attach or detach the plow blade and base assembly...

A complete, modular snowplow system for ATVs and UTVs designed to rapidly connect and disconnect without tools or crawling under the vehicle. The system is built in the U.S.A. and requires a plow blade, vehicle-specific plow mount kit, and a push tube. A ProVantage Electric-Lift or winch and winch mount kit are also recommended.

Extremely tough with excellent wear resistance, while still softer than steel. Perfect for use on sensitive surfaces like pavers and decorative concrete. 3/4" thick ultra high molecular weight polyethylene construction. Can squeegee water and fluids off hard surfaces. Reversible for double the wear life. Available for all blade sizes. Includes...

Actuator bracket kit for plow angle adjustment. Specifically designed for use with KFI UTV tubes, it rotates up to a full 25 degrees in both directions. Requires drilling. Made in the U.S.A.

A stiffener kit for use with the KFI 50" flex blade (PART #4501-1120, sold separately). It adds 8.4 lbs. to your flex blade. Made from 10ga grade 50 steel, it comes powdercoated black and includes hardware. Made in the U.S.A. NOTE: Drilling required for installation.

Designed for use with KFI UTV straight blades with a single hydraulic actuator. This kit includes OEM PART #S ACT-HR, ACT-HR-HAR, and ACT-HAR. It controls the winch for raising and lowering the plow system, and a single hydraulic actuator for angling a straight blade. The remote features a KFI logo backlit in blue when plugged in, a threaded...

A replacement lift cable for manual lift systems, used with plow mounting hardware.

Replace your old, broken, or outdated pulley bracket with this upgraded version. It is designed to keep your cable from coming off of the pulley and breaking. Features a quick and easy install and a powdercoated black finish.

A collection of individual replacement parts for the KFI Manual Lift system.

A dash-mounted rocker switch designed for use with the KFI plow hydraulic actuator (PART #4501-1126) and OEM PART #ACT-HAR (not included). This switch operates a single actuator (PART #4501-1126). Pro-V plow systems will require two of these kits. NOTE: Does not work with the wire harness hydraulic actuator PART #4501-1120 (OEM #105940).

A collection of individual replacement parts for KFI plow actuator systems. All parts are sold separately.

Replacement plow cradles made from 1/4" grade 50 steel construction. They are shot-blasted and finished with a tough powdercoated black finish. These cradles work with all KFI push tubes and are made in the U.S.A. Mounting hardware is not included.

Replaces the standard winch fairlead during plow season, providing a larger 2 1/8" diameter roller for smoother cable movement compared to standard 7/8" rollers. The roller has a curved cable groove to help eliminate cable flattening and potential cable kinking. Features multiple roller positions for different applications and cable angles. Models...

KFI 2.0 Glacier adapters designed to be permanently attached to the Pro 2.0 push tube (PART #4501-1004), keeping the plow mount off your machine during spring, summer and fall. Improper geometry can lead to a bad blade angle and/or force being applied incorrectly. The standard adapter's optimal mounting height is 14" from the ground, while the...